Plugin for Homeseer - xseer.zip

[billberet]

hey Jay,
i'm an Xseer Whore now too !!!!!!
and let me say damn i am happy.
Bill gave me some good advice and pointed me in the right dirrection.
i had so many left over x10 modules that were doing nothing, and now BAM
i'm back in business !!!!!
now i'm ordering more and more light switches and outlets and motion sensors, lol

MAKE IT STOP !!!!!!!

[Jay]

I'm sorry. I can't do that, Bill.

[Jay]

Hi Jay,
Thank you for your quick answer!!
I am going to follow your instruction today if I have enought of time...
I'll give you a feed back of my install..
Have a nice day!

Jay, when I've said 'it has ran one time' : the plugin was shown in xlobby and I was be able to set the server IP and user/password but it was impossible to user it. After a rebbot of xlobby it was impossible to view the plugin in the plugins menu of xlobby....

SD

Any joy?

[Jay]

hey Jay,
i'm an Xseer Whore now too !!!!!!
and let me say damn i am happy.
Bill gave me some good advice and pointed me in the right dirrection.
i had so many left over x10 modules that were doing nothing, and now BAM
i'm back in business !!!!!
now i'm ordering more and more light switches and outlets and motion sensors, lol

MAKE IT STOP !!!!!!!

A bit OT but do you have cameras to switch?
I have a nice HS2/XL solution, if so.

[billberet]

we'll have to talk about that
i could use a camera or 2

[Jay]

OK Bill, I'll send you some camera stuff offline from this board.

[steph@ne]

Hi Jay,
Sorry for my late answer..
This plugin is really wonderfull !!!
I have found all that I looked for ! The installation is very simple (with your instruction..).
I have receive the SW10 that I have ordered and it's a real pleasure to open/close with the xlobby interface.
Now, I have to bye a tablet pc to install it in my kitchen (to command all x10 modules SW10, lighting, AW12 and other thing ..)
I want to thank you again very much for your assistance !!!
SD

[Jay]

My pleasure.
Super plugin!

You prob noticed that when you upgrade XL, you need to reset your speaker client login, virtual device and tell it again to reconnect on startup. (in the plugin)

This is normal.

[Jay]

Finally updated HomeSeer2 to ver 2.4.0.6.

HS starts getting flooded with xseer plugin callback warnings every 30 seconds.

~!~Warning~!~In event #64 callback for plug-in xSeer, object not removed, error: Can not establish a connection to the remote host "_gtcp://0015854cb40b4d80aabf622773fa4739". Source: Microsoft.VisualBasic

This appears to happen when when an XL client is shut down - probably the server, too.
The flooding is preceded by the warning above, followed by:
~!~Network~!~Remote Speaker Client disconnected from 192.168.0.199
3/6/2010 8:35:00 PM ~!~ASR~!~Speaker Client speech recognition stopped
followed by the warning every 30 seconds.

This is disrupting some wireless X-10 events and I need to stop and reload HS2.

Anyone else seeing this?

[Bill Lott]

Hey stranger - great to see you active....

Yep. That has been a slight annoyance for awhile. It doesn't seem to affect anything other than filling up the Homeseer log with messages every couple of seconds...

I still think the two programs together are the best solution out there for someone wanting total home control!

Thanks again.

Bill

[Jay]

Hey Bill.
I took a closer look at this after your reply and the flood's not interfering as I thought. I had introduced a few variables like switching to lower power keyfobs in the cars for opening the garage,etc. and I changed the X-10 receiver's antenna location all at the same time I upgraded HS2.
Thanks for the reality check

Agreed. XL and HS2 is probably the most powerful combo out there.

I guess the 30 seconds between warnings is the period of the xseer heartbeat.